To attach bolt-on slide-rail assemblies to the rack:ġ.
#SUN FIRE X4150 1U SERVER INSTALL#
Repeat to install the remaining mounting-bracket on the other side of the server.Īttaching the Slide-Rail Assemblies to the Rackĭo one of the following procedures to attach the slide-rail assemblies to the rack: Verify that the rear locating pin has engaged the mounting-bracket clip. With the heads of the four chassis locating pins protruding though the four keyed openings in the mounting-bracket, pull the mounting-bracket toward the front of the chassis until the mounting-bracket clip locks into place with an audible click. Position a mounting-bracket against the chassis so that the slide-rail lock is at the server front, and the three keyed openings on the mounting-bracket are aligned with the three locating pins on the side of the chassis.įIGURE 2-2 Aligning the Mounting-bracket With the Server ChassisĢ. To install the mounting-brackets onto the sides of the server:ġ. Installing the Mounting-Brackets Onto the Server To remove the mounting-brackets from the tool-less slide-rail assemblies, refer to the install card instructions included with the kit. Repeat for the remaining slide-rail assembly.įIGURE 2-1 Disassembling the Bolt-on Slide-rail Before Installation Push the mounting-bracket release button toward the front of the mounting-bracket, as shown in FIGURE 2-1, and simultaneously withdraw the mounting-bracket from the slide-rail assembly.ĥ. Squeeze and hold the tabs at the top and bottom of the lock while you pull the mounting-bracket out of the slide-rail assembly until it reaches the stop. Locate the slide-rail lock at the front of one of the slide-rail assemblies, as shown in FIGURE 2-1.ģ. To remove the mounting-brackets from the bolt-on slide-rail assemblies:Ģ.
Preparing the Slide Rails and Server for Installation Disassembling Slide-Railsĭo one of the following procedures before installation: Consider the total airflow requirements of all equipment installed in the rack to ensure that the equipment is operated within its specified temperature range. Deploy your rack’s anti-tip bar to prevent the rack from tipping during equipment installation.Ĭaution - Ensure that the temperature in the rack does not exceed the server’s maximum ambient rated temperatures. Width: (not including ears): 16.75 inches (425.5 mm)Ĭaution - Always load equipment into a rack from the bottom up so that it will not become top-heavy and tip over. Length: (not including PSU handle): 28.0 inches (711.2 mm) Minimum 610 mm and Maximum 915 mm (24 inches to 36 inches).Ĭlearance depth in front of front mounting planeĭistance to front cabinet door is at least 25.4 mm (1 inch).Ĭlearance depth behind front mounting planeĭistance to rear cabinet door is at least 800 mm (31.5 inches) with the cable management arm, or 700 mm (27.5 inches), without the cable management arm.Ĭlearance width between front and rear mounting planesĭistance between structural supports and cable troughs is at least 456 mm (18 inches). Rack horizontal opening and unit vertical pitchĬonforms to ANSI/EIA 310-D-1992 or IEC 60927 standards.ĭistance between front and rear mounting planes The optional slide-rails are compatible with a wide range of equipment racks that meet the following standards:įour-post rack (mounting at both front and rear). The service label includes instructions for both tool-less and bolt-on rail assemblies.Ĭheck that your rack is compatible with the slide-rail and cable management arm (CMA) options.
#SUN FIRE X4150 1U SERVER HOW TO#
Refer to the service label on the Sun Fire X4150 server top cover for instructions on how to install your server into a four-post rack, using the slide-rail and cable management arm options. Instructions for both types are included in this chapter. The server might include either tool-less or bolt-on rail assemblies in rackmount kits. Verifying Operation of the Slide-rails and CMA Installing the Mounting-Brackets Onto the Serverĥ. To install your server into a four-post rack using the slide-rail and cable management arm options, perform the following tasks in the order shown:ģ. Read the overview and see the service label on the top cover before you begin to install the Sun Fire X4150 server.
0 kommentar(er)
